• CALL US

    303.778.1805

  • TOLL FREE

    1.800.648.9191

P6035 LC-2 LINE CLEANER TWO

CRYSTAL PACKAGING, INC.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: Crystal Packaging, Inc.
Address: 5185 National Western Dr. Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: August 28, 2007
PRODUCT NAME: LC-2 LINE CLEANER TWO
PRODUCT CODE: P6035
SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Nitric Acid 7697-37-2 TWA 2ppm TWA 2ppm/STEL 4ppm
Phosphoric Acid 7664-38-2 1mg/m3 1mg/m3

SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 150ºF Specific Gravity: 1.238
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Clear liquid with mild odor

SECTION IV: Fire and Explosion Hazard Data
Flash Point: N/A (Liquid not flammable)
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Carbon dioxide, dry chemical, foam or water. Class A, BC, or ABC fire extinguisher. Water spray recommended to avoid splashing.
Special Fire Fighting Procedures: Wear NIOSH approved self-contained breathing apparatus, goggles and special protective clothing. Water can be used to cool containers adjacent to fire.
Unusual Fire and Explosion Hazards: Contact with metal produces nitrogen gas which is very combustible. Pressure will develop in closed containers if temperatures over 150°F are achieved.

SECTION V: Reactivity Data

Stability: Stable
Conditions to Avoid: NA
Incompatibility: Metals, bases, oxidizing agents, organic solvents, carbides, sulfides, alkalis.
Hazardous Decomposition or Byproducts: Nitrogen gas, CO, CO², and smoke may be formed.
Hazardous Polymerization: Will not occur.

LC-2 LINE CLEANER TWO

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Contact will cause severe burns; possibility of impairment of vision.
Skin: Contact will cause severe burns.
Inhalation: Vapor is very irritating and toxic to lungs.

Emergency and First Aid Procedures

Eyes: Immediately flush with cool water for 15 minutes. Get immediate medical attention.
Skin: Immediately flush with large quantities of cool water while removing contaminated clothing and shoes until all acid is removed, paying particular attention to skin under nails. Follow by applying iced alcoholic or aqueous benzalkonium chloride solution, iced 70% alcohol or an ice cold saturated solution of magnesium sulfate (Epsom Salt). If these solutions are not available, continue washing in cool water or until medical attention is obtained. Wash clothing before reuse.
Inhalation: Immediately carry patient to fresh air and administer oxygen as soon as possible. If not breathing, give artificial respiration, preferably mouth to mouth.
Ingestion: DO NOT induce vomiting. Immediately give large quantities of water, milk, or milk of magnesia or eggs beaten with water. Never give anything by mouth to an unconscious person.

In case of contact or suspicion of contact, prompt medical attention is absolutely necessary!

LC-2 LINE CLEANER TWO

SECTION VII: Precautions for Safe Handling and Use
Steps to be taken in Case Material is released or spilled: Always wear protective clothing! For small spill: carefully neutralize with soda ash or lime. Then flush with large quantities of water if approved.
Waste Disposal Method: Dispose of in accordance with all federal, state and local regulations.
Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F is recommended. Store only in approved containers (avoid glass and some metals).
Other Precautions: Do not take internally or inhale vapors. Avoid all skin and eye contact.
SECTION VIII: Control Measure
Respiratory: Use NIOSH approved self-contained unit or supplied air.
Ventilation: As needed to control vapor level.
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Gauntlet type of Neoprene or plasticized.
Eye Protection: PVC. Chemical safety goggles and face shield.
Other Protective Clothing or Equipment: Full cover protective clothing including rubber boots and head protection.
CAUTION
Contains Nitric Acid. Can cause severe burns which may not be immediately painful or visible. May be fatal if inhaled or swallowed. Always wear proper gloves, goggles, aprons and boots when handling this product. In case of contact follow the first aid instructions below.

Here are a few cautionary tips:
1.) Do not get in eyes, on skin or on clothing.
2.) Do not breathe vapor or mist.
3.) Use only with adequate ventilation.
4.) Wash thoroughly after handling.
5.) Keep container closed.
6.) Keep out of reach of children.
7.) Store out of sun and away from heat.
8.) Open carefully to relieve possible internal pressure before completely removing closures.
9.) When opening container always wear rubber gloves, goggles, aprons, and boots. Vapor pressure on the skin may cause severe burns. If vapor pressure comes in contact with skin, flush immediately with copious amount of water.
10.) In case of a spill, flush immediately with water and neutralize with lime and flush again with water.
11.) In case of fire, use water spray to extinguish fire.

NA – Not Applicable NI – No Information

P6030 LC-1 LINE CLEANER ONE

CRYSTAL PACKAGING, INC.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: Crystal Packaging, Inc.
Address: 5185 National Western Dr. Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: August 28, 2007
PRODUCT NAME: LC-1 LINE CLEANER ONE
PRODUCT CODE: P6030
SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Soduim Hydroxide 1310-73-2 2 mg/m3 CL 2mg/m3 MAK:2mg/m3

SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 195ºF Specific Gravity: 1.418
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Soluble
Appearance and Odor: Pale clear liquid with mild odor

SECTION IV: Fire and Explosion Hazard Data
Flash Point: Non-combustible
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Use carbon dioxide, “alcohol form” or dry chemical where LC-1 is stored.
Special Fire Fighting Procedures: Pressure-demand, self contained respiratory protection and protective clothing should be worn by fire fighters in areas where LC-1 is stored.
Unusual Fire and Explosion Hazards: This product is not combustible nor does it support combustion.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Avoid contact with leather, wood, strong acids, Al, Sn, Zn and alloys containing these metals, and strong oxidizing agents.
Hazardous Decomposition or Byproducts: Carbon dioxide and Hydrogen gas.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

LC-1 LINE CLEANER ONE

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Caustic soda is destructive to eye tissues on contact. Will cause severe burns that result in damage to the eyes and even blindness.
Skin: Caustic soda is destructive to tissues contacted and produces severe burns.
Inhalation: Airborne concentrations of dust, mist, or spray of caustic soda may cause damage to the upper respiratory tract and even to the lung tissue proper which could produce chemical pneumonia, depending upon severity of exposure.
Ingestion: Caustic Soda can cause severe burns and complete tissue perforation of mucous membranes of the mouth, throat, esophagus, and stomach if swallowed.
Acute Overexposure: Burns, resulting in frequently deep ulceration and ultimate scarring.
Chronic Overexposure: The chronic local effect may consist of multiple areas of superficial destruction of the skin or of primary irritant dermatitis. Similarly, inhalation of dust, spray or mist may result in varying degrees of irritation or damage to the respiratory tract tissues and an increased susceptibility to respiratory illness.
Emergency and First Aid Procedures
SEEK MEDICAL ATTENTION IMMEDIATELY!
Eyes: Immediately flush eyes with large amounts of water for at least 15 minutes holding eyelids apart to ensure flushing of the entire eye surface. Washing eyes within 1 minute is essential to achieve maximum effectiveness. Seek Medical attention immediately.
Skin: Immediately wash contaminated skin with plenty of water. This may be followed with a rinse with vinegar or dilute acetic acid (3% solution) if available. Remove contaminated clothing and footwear and wash clothing before reuse. Discard footwear which cannot be decontaminated. Seek medical attention immediately.
Inhalation: Get person out of contaminated area to fresh air. If breathing has stopped, artificial respiration should be started. Oxygen may be administered, if readily available. Seek medical attention immediately.
Ingestion: If swallowed, DO NOT induce vomiting. Give large quantities of water. If available, give several glasses of milk. Never give anything by mouth to an unconscious person. Seek medical attention immediately.

LC-1 LINE CLEANER ONE

SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Stop leaks. Contain spill. Remove as much as possible (e.g. shovel up). Neutralize remaining traces of mineral with dilute acid; then flush area with water followed by liberal covering of sodium carbonate. Reuse spilled material, if possible, otherwise, place in closed, labeled container and store in a safe place to await proper disposal. Persons performing this work should wear adequate personal protective equipment and clothing.
Waste Disposal Method: Dispose of in accordance with all federal, state and local regulations concerning health and pollution. Dispose via approved chemical waste disposal, if regulations permit.
Precautions to Be Taken in Handling and Storing: Store in a dry area; avoid contact with acids.
Other Precautions: Do not take internally or inhale dust. Avoid eye
contact.

SECTION VIII: Control Measure
Respiratory: Use NIOSH approved respirator for dusts and mists. Use air purifying respirator when product is in contact with reducing sugars.
Ventilation:
Local Exhaust: Preferable to keep caustic soda below 2.0mg/m3
Mechanical (General): Acceptable
Protective Gloves: Rubber or PVC type gloves
Eye Protection: Chemical splash goggles and face shield.
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NA-Not Applicable NI- No Information

D7182 F-0-5 OXYGEN BLEACH

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: Crystal Packaging, Inc.
Address: 5185 National Western Dr. Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: March 5, 2008
PRODUCT NAME: F-0-5 OXYGEN BLEACH
PRODUCT CODE: D7182
NFPA: H-1 F-0 R-3 P-C
SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Hydrogen Peroxide 7722-84-1 1ppm 1ppm
SECTION III: Physical/Chemical Characteristics
Boiling Point: 195 degrees Specific Gravity: 1.058
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Clear liquid with no odor.

SECTION IV: Fire and Explosion Hazard Data
Flash Point: NA
Flammable Limits: NA LEL: NI UEL: NI
Extinguishing Media: Carbon dioxide, dry chemical, foam or water. Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus and protective clothing. Water can be used to cool containers adjacent to fire
Unusual Fire and Explosion Hazards: Product decomposes when heated which may cause rupture or explosion of containers. Vigorous reactions may occur with organic materials or oxidizing agents, which may result in a fire.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Heavy metals, reducing agents, organic, oxidizing agents
which may result in a fire.
Hazardous Decomposition or Byproducts: Oxygen.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

F-0-5 OXYGEN BLEACH

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Contact will be painful and irritating.
Skin: Prolonged contact may cause irritation.
Inhalation: May irritate nose, throat and chest.

Emergency and First Aid Procedures
Eyes: Flush with water for 15 minutes. Contact a physician.
Skin: Remove any contaminated clothing. Flush with water.
Inhalation: Remove to fresh air. If symptoms persist contact a physician immediately.
Ingestion: Dilute with milk or water and induce vomiting Contact a physician immediately. Do not use antacid or baking soda.
SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Wear protective clothing. Use non-combustible absorbent material and transfer to a disposal container.
Waste Disposal Method: In accordance with all federal, state, and local regulations.
Precautions to Be Taken in Handling and Storing: Store in a closed vented, clean container. Avoid sunlight. Storage between 40°F and 100°F is recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye and skin contact.
SECTION VIII: Control Measure
Respiratory: NIOSH approved respirator with acid canister for high concentrations.
Ventilation: Preferred
Local Exhaust: Required
Mechanical (General): Required
Protective Gloves: Rubber gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NA-Not Applicable NI- No Information

D7156 L. FRY OUT

BD Chemical Co. Inc.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: B-D Chemical Co. Inc.
Address: 701 Denargo Market Telephone Number: 303-296-3800
Denver, CO 80216 Date Prepared: March 20, 2003
PRODUCT NAME: LIQUID FRY OUT

SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other

Sodium Hydroxide 1310-73-2 2mg/m3 MAK: 2mg/m3

SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 195ºF Specific Gravity: 1.157
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Red liquid with pungent odor.

SECTION IV: Fire and Explosion Hazard Data
Flash Point: Non-flammable liquid.
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 195°F are reached.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Strong oxidizing agents or anything reactive with water.
Hazardous Decomposition or Byproducts: Carbon dioxide and Hydrogen gas.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

LIQUID FRY OUT

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Sodium Hydroxide is destructive to eye tissue on contact. Will cause severe burns that result in damage to eyes and even blindness.
Skin: Sodium Hydroxide is destructive to tissues contacted and produces severs burns.
Inhalation: Airborne concentrations of dust, mist, or spray of Sodium Hydroxide may cause damage to the upper respiratory tract and even to the lung tissue proper which could produce chemical pneumonia, depending upon severity of exposure.

Emergency and First Aid Procedures

Eyes: Immediately flush eyes with large amounts of water for at least 15 minutes, holding eyelids apart to ensure flushing of the entire eye surface. Washing eyes within 1 minute is essential to achieve maximum effectiveness. Seek medical attention immediately.
Skin: Immediately wash contaminated skin with plenty of water. This may be followed with a rinse with vinegar. Remove contaminated clothing and footwear and wash clothing before reuse. Discard footwear that cannot be decontaminated. Seek medical attention immediately.
Inhalation: Get person out of contaminated area to fresh air. If breathing has stopped, artificial respiration should be started. Oxygen may be administered if readily available. Seek medical attention immediately.
Ingestion: If swallowed, DO NOT induce vomiting. Give large quantities of water. If available, give several glasses of milk. Seek medical attention immediately.

SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Stop leaks. Contain spill. Remove as much as possible. Neutralize remaining traces of material with dilute acid, then flush area with water followed by a liberal covering of soda ash. Place in container and store in a safe place to await proper disposal. Persons performing this work should wear adequate personal protective equipment and clothing.
Waste Disposal Method: Dispose of in accordance with all federal, state, and local regulations concerning health and pollution. Dispose of via approved chemical waste disposal method if regulations permit.

LIQUID FRY OUT
Page 3

Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F are recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact.

SECTION VIII: Control Measure
Respiratory: Not normally needed.
Ventilation:
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NI – No Information NA – Not Available

________________________________________________________________

D7145 BOIL OUT

HADCO-DENVER

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: HADCO-DENVER
Address: 1339 W. CEDAR AVE. Telephone Number: 303-765-5806
Denver, CO 80223 Date Prepared: March 20, 2004
PRODUCT NAME: BOIL OUT #D7145

SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other

Sodium Hydroxide 1310-73-2 2mg/m3 MAK: 2mg/m3
Sodium Metasilicate 6834-92-0

SECTION III: Physical/Chemical Characteristics
Boiling Point: N/A Specific Gravity: N/A
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: White powder with mild odor.

SECTION IV: Fire and Explosion Hazard Data
Flash Point: Non-flammable solid.
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 195°F are reached.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Strong oxidizing agents or anything reactive with water.
Hazardous Decomposition or Byproducts: Carbon dioxide and Hydrogen gas.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

BOIL OUT

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Sodium Hydroxide is destructive to eye tissue on contact. Will cause severe burns that result in damage to eyes and even blindness.
Skin: Sodium Hydroxide is destructive to tissues contacted and produces severs burns.
Inhalation: Airborne concentrations of dust, mist, or spray of Sodium Hydroxide may cause damage to the upper respiratory tract and even to the lung tissue proper which could produce chemical pneumonia, depending upon severity of exposure.

Emergency and First Aid Procedures

Eyes: Immediately flush eyes with large amounts of water for at least 15 minutes, holding eyelids apart to ensure flushing of the entire eye surface. Washing eyes within 1 minute is essential to achieve maximum effectiveness. Seek medical attention immediately.
Skin: Immediately wash contaminated skin with plenty of water. This may be followed with a rinse with vinegar. Remove contaminated clothing and footwear and wash clothing before reuse. Discard footwear that cannot be decontaminated. Seek medical attention immediately.
Inhalation: Get person out of contaminated area to fresh air. If breathing has stopped, artificial respiration should be started. Oxygen may be administered if readily available. Seek medical attention immediately.
Ingestion: If swallowed, DO NOT induce vomiting. Give large quantities of water. If available, give several glasses of milk. Seek medical attention immediately.

SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Stop leaks. Contain spill. Remove as much as possible. Neutralize remaining traces of material with dilute acid, then flush area with water followed by a liberal covering of soda ash. Place in container and store in a safe place to await proper disposal. Persons performing this work should wear adequate personal protective equipment and clothing.
Waste Disposal Method: Dispose of in accordance with all federal, state, and local regulations concerning health and pollution. Dispose of via approved chemical waste disposal method if regulations permit.

BOIL OUT
Page 3

Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F are recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact.

SECTION VIII: Control Measure
Respiratory: Not normally needed.
Ventilation:
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NI – No Information NA – Not Available

________________________________________________________________

D7140 BIOSAFE

CRYSTAL PACKAGING, INC.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: Crystal Packaging, Inc.
Address: 5185 National Western Drive Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: January 12, 2006
PRODUCT NAME: BIOSAFE 3

SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Contains no hazardous components under current OSHA definitions. This material mixture formula is a trade secret and complies with 29CFR XVII- 1910.1200 Section (I) Trade Secrets. This formula contains no ingredients that are on the NTP list or registered with IARC for carcinogens and the material mixture tested as a whole has been found to be:
1) Non Toxic 2) Non Corrosive 3) Not an irritant 4) Not a sensitizer in oral, dermal and ocular tests on albino rats and rabbits per Federal Hazardous Substances Act (16CFR 1500.)

SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 212ºF Specific Gravity: 1.01
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than Butyl Acetate
Solubility in water: Soluble
Appearance and Odor: Yellow liquid with a pleasant lemon scent

SECTION IV: Fire and Explosion Hazard Data
Flash Point: Pensky-Martens closed tester.
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire
Unusual Fire and Explosion Hazards: Contains no unusual fire or explosive hazards.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Anything reactive with water.
Hazardous Decomposition or Byproducts: We have no studies of this product.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

BIOSAFE 3

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Contact will be painful and irritating.
Skin: Prolonged contact may cause irritation.
Inhalation: Will irritate nose, throat and chest.

Emergency and First Aid Procedures

Eyes: Flush with water for 15 minutes.
Skin: Flush with water.
Inhalation: Remove to fresh air. If any symptoms persist, contact a physician immediately.
Ingestion: Contact a physician immediately.
SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Flush away with water or soak up with sweeping compound or sand and transfer to a disposal container.
Waste Disposal Method: Bury, incinerate or flush to sewage disposal system In accordance with all federal, state, and local regulations.
Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F are recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact. If exposed to low temperatures (below 32°F) product may stratify. If so mix before using.
SECTION VIII: Control Measure
Respiratory: Not normally needed.
Ventilation:
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NA-Not Applicable NI- No Information

D7117 DEFOAM 1

BD Chemical Co. Inc.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: B-D Chemical
Address: 701 Denargo Market Telephone Number: 303-296-3800
Denver, CO 80216 Date Prepared: March 11, 2002
PRODUCT NAME: DEFOAM 1 (SILICONE)

SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
NONE
SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 212ºF Specific Gravity: 1.000
Vapor Pressure: NI Melting Point: NA
Vapor Density: N/A Evaporation Rate: 2.0
Solubility in water: DISPERSIBLE
Appearance and Odor: White opaque liquid with odor.
SECTION IV: Fire and Explosion Hazard Data
Flash Point: NA
Flammable Limits: NA LEL: NI UEL: NI
Extinguishing Media: Carbon dioxide, dry chemical, foam or ABC fire extinguisher.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire. Wear self-contained breathing equipment.
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 214°F are achieved.
SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Organic acids and inorganic bases.
Hazardous Decomposition or Byproducts: Oxides of Sulfur Hydrogen.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

DEFOAM 1 (SILICONE)

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Contact will be painful and destructive.
Skin: Prolonged contact may cause irritation and dryness.
Inhalation: May irritate nose, throat and chest.
Ingestion: May cause irritation.
Emergency and First Aid Procedures

Eyes: Flush with water for 15 minutes. While holding eyelids apart to ensure flushing of entire eye.
Skin: Remove any contaminated clothing. Flush with water.
Inhalation: Remove to fresh air. If any symptoms persist, contact a physician immediately.
Ingestion: Contact a physician immediately. Do not induce vomiting!
SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: For minor soak up with sweeping compound or sand and transfer to a disposal container.
Waste Disposal Method: Bury, incinerate or flush to sewage disposal system In accordance with all federal, state, and local regulations.
Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F are recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact.
SECTION VIII: Control Measure
Respiratory: Not normally needed.
Ventilation:
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Rubber gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NA-Not Applicable NI- No Information

D7110 HIGH FOAM

CRYSTAL PACKAGING, INC.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: CRYSTAL PACKAGING, INC.
Address: 5185 National Western Dr. Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: June 12, 2007
PRODUCT NAME: HIGH FOAM
PRODUCT CODE: D7110
SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Ethylene Glycol Monobutyl Ether
111-76-2 25000 20000
ppm TWA (Skin) ppmTWA (Skin)
SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 190ºF Specific Gravity: 1.056
Vapor Pressure: NA Melting Point: NA
Vapor Density: Lighter than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Clear light yellow with mild alcohol odor.
SECTION IV: Fire and Explosion Hazard Data
Flash Point: NA Greater than 200°F (PENSKE-MARTIN TEST)
Flammable Limits: NA LEL: NI UEL: NI
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Water can be used to cool containers
adjacent to fire.
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 190°F are reached.
SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Strong oxidizing agents, alkali, lime, or anything reactive with
water or alcohol
Hazardous Decomposition or Byproducts: Carbon monoxide, carbon dioxide,
Sulfur dioxide, hydrogen sulfide, ammonia and smoke.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

High Foam

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion
Effects of Overexposure
Eyes: Contact will be painful and irritating.
Skin: Prolonged contact may cause irritation.
Inhalation: Will cause giddiness.
Emergency and First Aid Procedures
Eyes: Flush with water for 15 minutes.
Skin: Remove any contaminated clothing. Flush with water.
Inhalation: Remove to fresh air. Contact a physician immediately.
Ingestion: Contact a physician immediately.
SECTION VII: Precautions for Safe Handling and Use
Steps to be taken in Case Material is released or spilled: Flush with water or soak up with sweeping compound or sand and transfer to a disposal container with non-sparking equipment.
Waste Disposal Method: In accordance with all federal, state, and local regulations.
Precautions to Be Taken in Handling and Storing: Store in a cool well-ventilated area.
Other Precautions: Do not take internally or inhale vapors. Avoid eye
Contact.
SECTION VIII: Control Measure
Respiratory: Not normally needed. However, if strong fumes are present, use a NIOSH or MESA approved gas mask for organic vapors.
Ventilation:
Local Exhaust: Provide adequate ventilation to keep concentration below
TLV.
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.
NA-Not Applicable NI- No Information
SECTION IX: Dot Shipping Information
Compounds, cleaning liquid (contains Hydrochloric acid, Phosphoric acid), 8, NA1760, PGII

NA – Not Applicable NI – No Information

D7109 DRILL TERGE

BD Chemical Co. Inc.

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: B-D Chemical
Address: 701 Denargo Market Telephone Number: 303-296-3800
Denver, CO 80216 Date Prepared: February 15, 2002
PRODUCT NAME: CETCO DRILL TERG

SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other

NONE
SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 190ºF Specific Gravity: 1.080
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Clear blue liquid with a mild odor.

SECTION IV: Fire and Explosion Hazard Data
Flash Point: NA Liquid not flammable
Flammable Limits: NA LEL: NI UEL: NI
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire.
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 190°F are reached.

SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Strong oxidizing agents, alkali, lime, or anything reactive with water.
Hazardous Decomposition or Byproducts: Carbon monoxide, carbon dioxide, ammonia and smoke.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA

CETCO DRILL TERG

SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion

Effects of Overexposure
Eyes: Contact will be painful and irritating.
Skin: Prolonged contact may cause irritation.
Inhalation: May irritate nose, throat and chest.

Emergency and First Aid Procedures

Eyes: Flush with water for 15 minutes.
Skin: Remove any contaminated clothing. Flush with water.
Inhalation: Remove to fresh air. If symptoms persist contact a physician immediately.
Ingestion: Contact a physician immediately.

SECTION VII: Precautions for Safe Handling and Use

Steps to be taken in Case Material is released or spilled: Flush with water or soak up with sweeping compound or sand and transfer to a disposal container.
Waste Disposal Method: In accordance with all federal, state, and local regulations.
Precautions to Be Taken in Handling and Storing: Store in a cool well ventilated area.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact.

SECTION VIII: Control Measure
Respiratory: Not normally needed. However if strong fumes are present, use a NIOSH or MESA approved gas mask for organic vapors.
Ventilation:
Local Exhaust: Preferred
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.

NA-Not Applicable NI- No Information

SECTION IX: Dot Shipping Information

Compounds, cleaning liquid (contains Hydrochloric acid, Phosphoric acid), 8, NA1760, PGII

NA – Not Applicable NI – No Information

D7105 LOW TEMP WAREWASH

Material Safety Data Sheet

SECTION I
Manufacturer’s Name: Crystal Packaging, Inc. Address: 5185 National Western Drive Telephone Number: 303-778-1805
Denver, CO 80216 Date Prepared: 09/09/07 PRODUCT NAME: LOW TEMP WAREWASH
PRODUCT CODE: 03-D7105
SECTION II: Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Other
Sodium Hydroxide 1310-73-2 2mg/m3 MAK: 2mg/m3
SECTION III: Physical/Chemical Characteristics
Boiling Point: Approximately 195ºF Specific Gravity: 1.157
Vapor Pressure: NA Melting Point: NA
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Solubility in water: Complete
Appearance and Odor: Red liquid with pungent odor.
SECTION IV: Fire and Explosion Hazard Data
Flash Point: Non-flammable liquid.
Flammable Limits: NA LEL: NA UEL: NA
Extinguishing Media: Carbon dioxide, dry chemical, foam or water.
Class A, BC, or ABC fire extinguishers.
Special Fire Fighting Procedures: Water can be used to cool containers adjacent to fire
Unusual Fire and Explosion Hazards: Pressure may develop in closed containers if temperatures over 195°F are reached.
SECTION V: Reactivity Data
Stability: Stable
Conditions to Avoid: NA
Incompatibility: Strong oxidizing agents or anything reactive with water.
Hazardous Decomposition or Byproducts: Carbon dioxide and Hydrogen gas.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: NA
SECTION VI: Health Hazard Data
Routes of Entry: Eye contact, Skin contact, Inhalation, and Ingestion
Effects of Overexposure
Eyes: Sodium Hydroxide is destructive to eye tissue on contact. Will cause severe burns that result in damage to eyes and even blindness.
Skin: Sodium Hydroxide is destructive to tissues contacted and produces severs burns.
Inhalation: Airborne concentrations of dust, mist, or spray of Sodium Hydroxide may cause damage to the upper respiratory tract and even to the lung tissue proper which could produce chemical pneumonia, depending upon severity of exposure.
LOW TEMP WAREWASH
PAGE 2
Emergency and First Aid Procedures

Eyes: Immediately flush eyes with large amounts of water for at least 15 minutes, holding eyelids apart to ensure flushing of the entire eye surface. Washing eyes within 1 minute is essential to achieve maximum effectiveness. Seek medical attention immediately.
Skin: Immediately wash contaminated skin with plenty of water. This may be followed with a rinse with vinegar. Remove contaminated clothing and footwear and wash clothing before reuse. Discard footwear that cannot be decontaminated. Seek medical attention immediately.
Inhalation: Get person out of contaminated area to fresh air. If breathing has stopped, artificial respiration should be started. Oxygen may be administered if readily available. Seek medical attention immediately.
Ingestion: If swallowed, DO NOT induce vomiting. Give large quantities of water. If available, give several glasses of milk. Seek medical attention immediately.
SECTION VII: Precautions for Safe Handling and Use
Steps to be taken in Case Material is released or spilled: Stop leaks. Contain spill. Remove as much as possible. Neutralize remaining traces of material with dilute acid, then flush area with water followed by a liberal covering of soda ash. Place in container and store in a safe place to await proper disposal. Persons performing this work should wear adequate personal protective equipment and clothing.
Waste Disposal Method: Dispose of in accordance with all federal, state, and local regulations concerning health and pollution. Dispose of via approved chemical waste disposal method if regulations permit.
Precautions to Be Taken in Handling and Storing: Storage between 40°F and 100°F are recommended.
Other Precautions: Do not take internally or inhale vapors. Avoid eye contact.
SECTION VIII: Control Measure
Respiratory: Not normally needed.
Ventilation:
Local Exhaust: Preferable
Mechanical (General): Acceptable
Protective Gloves: Plastic or NBR gloves
Eye Protection: Chemical safety goggles
Other Protective Clothing or Equipment: Usually not needed unless splashing is excessive.
NI – No Information NA – Not Available

________________________________________________________________